News:

Hi!

Welcome to my DIY audio forum. The forum SW has been reset and unfortunately there were some problems with backup files so a few posts were lost, nothing important though.

Cheers
Per-Anders Sjöström

Main Menu

Recent posts

#11
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by W1DAN - January 31, 2021, 05:34:59 PM
Hi Per Anders:

Adding 330PF capacitors directly at the base of T35 and T36 (paralleling C17 andC18 except close to the transistors) reduces the oscillation at the output of the preamp section without affecting the frequency response at 20KHz. Earlier I tried an 0.1uf capacitor and 10KHz was attenuated by more than half, so that was no good.

I am wondering if the physical distance of C17 and C18 to the bases of the emitter followers allows the oscillation?

On to the RIAA section!

Thank you,
Dan
#12
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by peranders - January 31, 2021, 04:26:35 PM
If you use the keywords "emitter follower oscillation", I'm sure you can find something.

I think you can put that aside and try to get the RIAA stage to get working properly.
#13
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by W1DAN - January 31, 2021, 02:43:40 PM
Per Anders:

Each transistor is mounted between 0.6cm to 1cm above the board.

I thought being an emitter follower, which normally having gain less than 1, could not oscillate?

Thank you,
Dan
#14
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by peranders - January 31, 2021, 07:14:43 AM
Emitter followers can oscillate under certain conditions although it's much easier with power mosfets. How near the pcb have you mounted the transistors?
#15
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by W1DAN - January 30, 2021, 11:31:54 PM
Per Anders:

The oscillation goes away when the power is turned off.

Definitely coming from the preamp sections, not the RIAA stages. I lifted R50 to separate the gain stage from the emitter followers. The oscillation appears at the emitter follower section. I confirmed that C103 and C104 are 100nF.

I also am a radio ham and broadcast engineer, and work on RF on both my radio hobby and at work, but there with slightly higher power of 88kW. :-)

Dan
#16
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by peranders - January 30, 2021, 09:07:17 PM
If you turn off the power, do you still have the oscillation? For being an oscillation with BC transistors I think the frequency is very high. 1-10 MHz seems more natural.
#17
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by W1DAN - January 30, 2021, 07:49:29 PM
Hi Per Anders:

Thank you for quick replies today. This is enjoyable.

I edited my previous post as you posted, please read again.

Yes I have an older analog oscilloscope that is good for RF. The scope case is grounded to the preamp chassis case, and the scope probe ground lead is connected to the ground pin of J2. The preamp card Chassis ground connection is connected to the preamp chassis.

Both preamp channels oscillate. I checked with a spectrum analyzer too. Good transmitter at 284MHz!

Thank you,
Dan
#18
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by peranders - January 30, 2021, 07:31:57 PM
Good that you have found a point where the servo doesn't hit the roof. The output offset in TP1 should be the value which the OP07 has, single millivolts is fine. The DC servo doesn't contribute to any noise since it's heavily filtered. Nice that one channel works. Now you have to check the other channel.

Do you have the oscillation in both channels? Do you have an oscilloscope capable of 350 MHz or more? Make sure your ground wire of the probe is wounded around the probe and connected very near the TP1. A long ground wire serves as an antenna. If possible you should use a ground needle on the probe tip.
#19
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by W1DAN - January 30, 2021, 05:40:26 PM
Per Anders:

More tests on IC5:
Add -15v to IC5 socket (no IC inserted) pin 5, TP1 moves from -180mv to -190mv
Add +15v to IC5 socket (no IC inserted) pin 5, TP1 no change T -238mv.
Shorting IC5 pin 5 to ground, TP1 = -237mv.

New tests on IC1:
IC1 (OP07C inserted), input shorted to ground, IC5 socket empty:
Pin 1 = +14.975
Pin 2 = -1mv
Pin 3 = -149mv
Pin 4 = -15.011v
Pin 5 = +0.2mv
Pin 6 = -14.321v
Pin 7 = +15.033v
Pin 8 = +14.919v

With IC1 removed, TP1 is at -300mv. Adding -20v to IC socket pin 6 (no IC inserted), TP1 reduces to -170mv.

Added 22K across R29, added 100k across R27. Bench supply of -9.5v at pin 6 now creates 0v at TP1!! With IC1 (OP07) installed, TP1 is now -7.5mv. Good! Will this increase noise from OP07 to preamp?

Inserting a 1KHz sine wave to the input causes IC1 servo to oscillate at about 40hz. Adding 10uf at the output of R29 eliminates this. Using an oscilloscope, I now see crossover distortion on the test sine wave at the card output, possibly from the RIAA stage-will look at this later.

If this servo change is approved by you, we now need hints on eliminating the 284MHz RF oscillation (this is not from a Radio Sweden International transmitter, but generated in the preamp). With the input shorted, the RF signal is 70mv p-p at TP1.

Thank you!
Dan
#20
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by peranders - January 30, 2021, 05:25:32 PM
Sorry, I was mistaken here. The opamp in mind here is IC1. Is it populated? If yes, please measure pin 2, 3, 4, 6 and 7?