News:

Hi!

Welcome to my DIY audio forum. The forum SW has been reset and unfortunately there were some problems with backup files so a few posts were lost, nothing important though.

Cheers
Per-Anders Sjöström

Main Menu

Recent posts

#1
Power supplies / Re: SST 01 Rev 1
Last post by peranders - December 06, 2024, 04:03:40 PM
T2 is suspect since you can't have more than 1 V across base-emitter.
#2
Power supplies / Re: SST 01 Rev 1
Last post by peranders - December 06, 2024, 04:03:11 PM
Last Edit: Yesterday at 06:06:23 PM by Esprit
heaveno, I have two of the SST01 rev.1, one each in mono Pass F5t.
Following application of 24v across DZ1, the following results were obtained.


PCB No1
T3, B/E= 0v.    C/E= 22v
T2, B/E= 23v.   C/E= 23.1v
T1, B/E= 143mv. C/E= 40mv


PCB No2
T3, B/E= .94v.  C/E= 60mv
T2, B/E= .4v.   C/E= 22.2v
T1, B/E=.623v.  C/E= 1mv
#3
Power supplies / Re: SST 01 Rev 1
Last post by peranders - December 06, 2024, 04:02:29 PM
December 02, 2024, 09:09:24 AM
No worries. Take your time.
#4
Power supplies / Re: SST 01 Rev 1
Last post by peranders - December 06, 2024, 04:01:41 PM
November 29, 2024, 11:26:43 AM
Please accept my apologies for the delay in answering (I am waiting the return of my bench power supply)
#5
Power supplies / Re: SST 01 Rev 1
Last post by peranders - December 06, 2024, 04:01:20 PM
November 21, 2024, 06:36:30 PM
First of all (if possible) use a 24 V source with current limitation. It's much safer not having live voltage.


Connect 24 V across the DZ1 zener or similar point. Start with T3 and go backwards. What is the base-emitter voltage on T3? Should be 650 mV and the collector-emitter voltage less than 200 mV.
#6
Power supplies / SST 01 Rev 1
Last post by peranders - December 06, 2024, 04:00:48 PM
heaveno Folks very new to this forum


After two years of uninterrupted service, Relay K2 fails to latch.
When power is applied the points continuously bounce, is there a fix.
#7
Power supplies / Re: SSR01 => unregulated DC in...
Last post by peranders - April 06, 2022, 07:44:50 PM
For inspiration you can check how SSR04 is designed.

Important for design: What is the max current consumption of your amps?
#8
Power supplies / SSR01 => unregulated DC input ...
Last post by kunlun121 - April 03, 2022, 07:30:17 PM
Hi Per-Anders,

I'm trying to figure out how to best provide unregulated DC power to the SSR01 boards. I am using a toroidal transformer and a basic discrete full wave bridge rectifier with some smoothing caps before the SSR01.

I'd like to know how much smoothing is necessary. Or better, the minimum amount of smoothing I can get away with. Can you advise about the minimum total size of the smoothing capacitance required for optimal operation of the super regulators? Or would you advise to maximise smoothing capacitance given the available space on my boards?

The application at hand is the 30V version I ordered the boards for. I want to use it for a minimalistic phono stage, so the load is pretty insignificant. But I'd like to know this number for different voltages / applications too. Is there relatively straightforward way of calculating that for different voltages? What are the relevant variables in determining the minimum smoothing capacity?

Thank you for looking into this.

BTW and off-topic: please find some other way of ascertaining that I am not a robot. These letter combination images are impossible to read, also for a living breathing if ageing human in need of reading glasses...
#9
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by W1DAN - February 13, 2021, 01:57:44 AM
Hej Per Anders!

I would like to increase the gain about 6dB. Would I increase R51 to do this?

I am using a MM cartridge and the preamp is working pretty well (still have an issue with the right channel DC offset without input termination).

Thank you,
Dan
#10
Phono RIAA amplifiers / Re: QSXM2 troubleshooting!!
Last post by W1DAN - February 01, 2021, 02:57:29 AM
Per Anders:

The RIAA stage came up fine for the left channel. On the right channel RIAA section I still have some offset on the output when the preamp has 10mv at TP1. For now I inserted a 10UF capacitor in series with R93, and the main output DC is now fine.

On the preamp DC servo amp IC1, when my test oscillator is set to 20hz, I see a sine wave on the output pin 6, as well as a little at C9. Would this AC audio correction signal "subtract" the from the main signal low frequency audio? Either way I added 10uF across C9 to make the correction voltage pure DC.

I'm listening to the preamp now-sounds clean. I will then look for the cause of the right channel DC offset and eliminate the audio coupling capacitor.

Good progress this weekend! Thank you again for your assistance!!

Cheers,
Dan