News:

Hi!

Welcome to my DIY audio forum.

Cheers
Per-Anders Sjöström

Main Menu

dct-01 question...

Started by rtate, April 03, 2008, 05:55:01 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

rtate

I have 8 mono blocks built with toroid transformers and a few of them have a hum or buzz.
I am considering the dct-01 as a possible solution and was wondering if Icould just use one dct-01 on the supply to the power bar instead of one for each amplifer??

The amps are "leach superamps" 250 watts and use 10 amp transformers with 80,000uf capacitance. 115 VAC mains
I am currently in the process of installing soft start circuits in each amp.
7 Leach superamps, 3 shiva subs,Aria5R
Parasound AVC2500u, Sugden transport,
Bride of Zen preamp,home made Cat5 speakecable
and interconnects

peranders

If you connect them to the same outlet, do them hum equally much?
/Per-Anders Sjöström, owner of this forum

Homepage with my DIY hifi stuff

rtate

The amps are fed from a dedicated 20 amp breaker run with 10 gauge wire.
There are no other devices on this circuit.
One wall recepticle feeds a power bar where the amps are plugged in.
I do not think that they all hum equally and the volume of the hum seems to rise and fall in no particular pattern.
I am wondering if this is a product of several hard starts over the 4 years that they have been in service.
The hum seems to have gotten worse over time.
I just thought that if I put the trap before the wall recepticle I could clean up the signal before it gets to the power bar.
7 Leach superamps, 3 shiva subs,Aria5R
Parasound AVC2500u, Sugden transport,
Bride of Zen preamp,home made Cat5 speakecable
and interconnects

peranders

If you have a hum that comes and goes, then it might be DC which is causing this.
/Per-Anders Sjöström, owner of this forum

Homepage with my DIY hifi stuff

rtate

So my question is, can i use one trap to clean up the mains feen or do i have to use one for each amplifer on the circuit/
7 Leach superamps, 3 shiva subs,Aria5R
Parasound AVC2500u, Sugden transport,
Bride of Zen preamp,home made Cat5 speakecable
and interconnects

peranders

The limit is set by the diodes and the size of the caps. I should recommend one trap to each amp.
/Per-Anders Sjöström, owner of this forum

Homepage with my DIY hifi stuff

rtate

If I put one in each amp should I put it before or after the softstart circuit.

Do you have suitable part numbers for the diodes, and values for the capacitors so that I can build a proto-type before i order the pcb's

THANKS.
7 Leach superamps, 3 shiva subs,Aria5R
Parasound AVC2500u, Sugden transport,
Bride of Zen preamp,home made Cat5 speakecable
and interconnects

peranders

It doesn't matter where you put it.

Diode: 6 A or more, voltage rating > 10 V

Cap: 10000 uF or more, >25 V but I should think 16 V would work. Max DC voltage is only 1-3 V.
/Per-Anders Sjöström, owner of this forum

Homepage with my DIY hifi stuff

rtate

 P-A just to confirm again:

1) If I were to use 6 diodes as per your schematic rated at 6 amp, this would be ok for  1000va transformers with 80,000uf capacitance placed before my softstart circuit.

2) In the trap circuit is there a benefit to more capacitance?

3) Which line woud you put the trap on  Hot or neutral and why?

4) Why not on both hot and neutral?

Space in my chassis is not a concern for component size.
7 Leach superamps, 3 shiva subs,Aria5R
Parasound AVC2500u, Sugden transport,
Bride of Zen preamp,home made Cat5 speakecable
and interconnects

peranders

1) Start with 2 diodes. Current flows in the diodes only at start up. The unit is intended for home use, not hard professional duty.

2) Yes

3) Doesn't matter

4) Only in series with the primary winding, that's enough.
/Per-Anders Sjöström, owner of this forum

Homepage with my DIY hifi stuff